[bsd-nomads:16347] ThinkPad T23 とICH Audio Driver

[TOKITA Miki <miki98@mail3.alpha-net.ne.jp>]

初めてメールします。
久保と申します。

ThinkPad T23(2647-9JJ)でサウンドを鳴らす方法がわからないのでお尋ねします。
[bsd-nomads:15913]以下のスレッドは一通り目を通したのですが、根本的な事が
わかっていないので手が出ない状態です。

使用OSはFreeBSD 4.6-RCになります。
GENERICカーネルに以下の４行を加え、
device          smbus
device          smb
device          ichsmb
device          pcm

また以下の１行を削除した状態のdmesgを下に付けておきます。
device          eisa

なぜかわかりませんが、eisaが有効な状態でサウンドドライバ(カーネル・
loader.confにかかわらず)を組み込むと下の「★☆★」のところでOSの起動が止
まってしまいます。eisaを組み込まなければ(音はならなくても)起動自体は問題
なくできるのですが。



それで、[bsd-nomads:15913]の830MP.diffというファイルを具体的にどのように
使うのかわからないので、教えてください。
この話題が出た時とは同じT23でもOSのバージョンもチップの型番(82801BA→
82801CA)も違いますが、とりあえず試してみたいと思っています。

どうぞ宜しくお願いします。

-- 
real:久保 貴美
handle:ときたみ
miki98@mail3.alpha-net.ne.jp
http://homepage2.nifty.com/tokitami/index.htm



Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 4.6-RC #1: Wed Jun  5 21:06:57 JST 2002
    miki@konoe.my.domain:/usr/src/sys/compile/KONOE
Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (799.32-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6b1  Stepping = 1

Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 670433280 (654720K bytes)
avail memory = 646328320 (631180K bytes)
Preloaded elf kernel "kernel" at 0xc051c000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 14 entries at 0xc00fdeb0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI to PCI bridge (vendor=8086 device=3576)> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <S3 model 8c2e graphics accelerator> at 0.0 irq 11
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port
0x1800-0x181f irq 11 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port
0x1820-0x183f irq 11 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0x1840-0x185f irq 11 at
device 29.2 on pci0
uhci2: (New UHCI DeviceId=0x24878086)
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: (0x24878086) UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pcib2: <PCI to PCI bridge (vendor=8086 device=2448)> at device 30.0 on pci0
pci2: <PCI bus> on pcib2
pcic0: <TI PCI-1420 PCI-CardBus Bridge> mem 0x50000000-0x50000fff irq 11
at device 0.0 on pci2
pcic0: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
pccard0: <PC Card bus (classic)> on pcic0
pcic1: <TI PCI-1420 PCI-CardBus Bridge> mem 0x51000000-0x51000fff irq 11
at device 0.1 on pci2
pcic1: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
pccard1: <PC Card bus (classic)> on pcic1
wi0: <Intersil Prism2.5> mem 0xec000000-0xec000fff irq 11 at device 2.0
on pci2
wi0: 802.11 address: 00:20:e0:89:7a:c3
wi0: using RF:PRISM2.5 MAC:ISL3874A(Mini-PCI)
wi0: Intersil Firmware: Primary 1.00.05, Station 1.03.03
fxp0: <Intel Pro/100 Ethernet> port 0x7000-0x703f mem
0xc0200000-0xc0200fff irq 11 at device 8.0 on pci2
fxp0: Ethernet address 00:d0:59:34:58:12
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI to ISA bridge (vendor=8086 device=248c)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 ATA100 controller> port
0x1860-0x186f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device
31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
ichsmb0: <Intel 82801CA (ICH3) SMBus controller> port 0x1880-0x189f irq
11 at device 31.3 on pci0
smbus0: <System Management Bus> on ichsmb0
smb0: <SMBus general purpose I/O> on smbus0
pcm0: <Intel 82801CA (ICH3)> irq 11 at device 31.5 on pci0
pcm0: unable to map IO port space
device_probe_and_attach: pcm0 attach returned 6
★☆★pci0: <unknown card> (vendor=0x8086, dev=0x2486) at 31.6 irq 11
orm0: <Option ROMs> at iomem
0xc0000-0xcdfff,0xce000-0xcefff,0xcf000-0xcffff,0xdc000-0xdffff,0xe0000-0xeffff
on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: parallel port not found.
ad0: 45780MB <IC25T048ATDA05-0> [93015/16/63] at ata0-master UDMA100
Mounting root from ufs:/dev/ad0s3a